Tito Mon Posted November 24, 2013 Report Share Posted November 24, 2013 My journey need to replace the rear brake pads,, is CANADIAN TIRE is a good to go for brake maintenance or the DEALER? any suggestion please?,, thanks guys Quote Link to comment Share on other sites More sharing options...
rolly Posted November 24, 2013 Report Share Posted November 24, 2013 Dealer will most likely be more expensive, as for Canadian Tire I've had good results over the years on many of my vehicles. Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
jkeaton Posted November 24, 2013 Report Share Posted November 24, 2013 Not that hard to do yourself. Save even more money. Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
Tito Mon Posted November 24, 2013 Author Report Share Posted November 24, 2013 thank you guys,, maybe i'll go to canadian tire,, i want to do it but i have no room for under graound parking,, thank you,, i appreciate that Quote Link to comment Share on other sites More sharing options...
Journey_SeXT Posted November 24, 2013 Report Share Posted November 24, 2013 For simple maintenance like brakes, tires, oil changes, tuneups, etc... they are alright but any major repairs I would strongly suggest looking elsewhere. Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
jkeaton Posted November 24, 2013 Report Share Posted November 24, 2013 Do you have anyone else besides Canadian Tire up there? Seems like every forum I'm on, the Canadians are talking about Canadian Tire.....are they like a Firestone or something? What are other options for vehicle repair? Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
wingit11 Posted November 24, 2013 Report Share Posted November 24, 2013 I have not had good experience with Canadian Tire. Seems that they do not have very experienced mechanics and always want to up sell me for work that is not needed. Fortunately I can do most of the routine stuff myself, but when I do need work done that I cannot (or don't want to) do I use a independent shop that was highly recommended to me. Working out good so far. Of course the DJ is still under warranty so it goes to the dealer. Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
Journey_SeXT Posted November 25, 2013 Report Share Posted November 25, 2013 (edited) Do you have anyone else besides Canadian Tire up there? Seems like every forum I'm on, the Canadians are talking about Canadian Tire.....are they like a Firestone or something? What are other options for vehicle repair? Yes we have other chains like Midas, Speedy, Master Mechanic etc...... Canadian Tire has been around forever so people like the convenience of their garage. Here is their website if you would like to see what they offer: http://www.canadiantire.ca/en.html They also have their auto garage attached to the store. They own Part Source which is the equivalent to Autozone & Advance Auto in the U.S. Advance Auto if I am not mistaken is also owned by Canadian Tire/Parts Source. Edited November 25, 2013 by Journey_SeXT Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
Tito Mon Posted November 25, 2013 Author Report Share Posted November 25, 2013 i like this forum guys, i learned,, thanks for suggestion,, i want to do it by my self but i don't have tools like c clamp or the special tools,, Quote Link to comment Share on other sites More sharing options...
bigtsr Posted November 25, 2013 Report Share Posted November 25, 2013 You can rent tools. Inquire at Cantire,PartSource or Napa stores. Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
jkeaton Posted November 25, 2013 Report Share Posted November 25, 2013 (edited) You can rent tools. Inquire at Cantire,PartSource or Napa stores. Very true. Most stores will rent you the tools. They normally charge what the tool set would cost new, but then refund it when you bring them back. Or, if your like me, I just decide I could use the tools and end up keeping them. You can also get brake tool kits off ebay for cheap. I got a kit for calipers that includes all the adapters for all makes of vehicles for under $30. Most of the newer rear brakes can't use a plain old c-clamp to seat the piston, you have to turn the piston while pressing it in, those kits are a life saver to be. I used to do it with a pair of needle nose pliers. Took forever! Edited November 25, 2013 by jkeaton Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
Tito Mon Posted December 7, 2013 Author Report Share Posted December 7, 2013 I'm thinking also to do it by myself about the rear brake pads,, is that easy to do it? any suggestion pls? Quote Link to comment Share on other sites More sharing options...
jkeaton Posted December 7, 2013 Report Share Posted December 7, 2013 (edited) I'm thinking also to do it by myself about the rear brake pads,, is that easy to do it? any suggestion pls? Easy enough. Unbolt the calipers, remove the pads, seat the piston (remove the brake fluid reservoir and remove some brake fluid so it does not overflow when the fluid gets pushed back into it), as stated above, you need a special tool to turn the brake piston in while puching it. Install the new pads, reinstall the caliper. Message me if you need assistance. Edited December 7, 2013 by jkeaton Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
Journey_SeXT Posted December 8, 2013 Report Share Posted December 8, 2013 (edited) Tito Mon: Here is a thread I started with a youtube clip showing the rear pad and rotor replacement......http://www.dodgejourneyforum.com/topic/3467-2009-dodge-journey-replace-rear-rotors-pads-video/ Edited December 8, 2013 by Journey_SeXT Tito Mon 1 Quote Link to comment Share on other sites More sharing options...
Tito Mon Posted December 8, 2013 Author Report Share Posted December 8, 2013 to JKEATON; I saw that there was a anti-squeek? or other spray at the back of the pads (what I saw in video of Journey_sext) do I have to put that? what if after I put the new pads w/o spraying (just clean all the dust & wipe it) is that ok? Quote Link to comment Share on other sites More sharing options...
2late4u Posted December 8, 2013 Report Share Posted December 8, 2013 (edited) do what the pad manufacture says to do . i know wagner thermo-quite pads say if you use anything it will void the warrenty dont know why. but i use them all the time and will use them for my journey this spring when i do both the front and back i am at 60k miles right now. Edited December 8, 2013 by 2late4u pacsound 1 Quote Link to comment Share on other sites More sharing options...
jkeaton Posted December 10, 2013 Report Share Posted December 10, 2013 As stated above, if the pad manufacturer states to use anti squeal then use it. Some higher end pads come with it included. Some don't require it. The only thing I use when putting it all back together is spread anti-seize compound on any metal to metal contact areas. Never had an issue or squeals. Quote Link to comment Share on other sites More sharing options...
FROGBOX Posted December 11, 2013 Report Share Posted December 11, 2013 i like this forum guys, i learned,, thanks for suggestion,, i want to do it by my self but i don't have tools like c clamp or the special tools,, If you don't mind a drive to Whitby, I can help you. Buy the parts and I can help you install them. I have the brake piston rewind tool. There is more to replacing rear pads than just changing parts. You also need to lube the sliders and clean & lube the guides that the pads sit in. Otherwise, they will stick and drag on the rotors, causing premature wear. rolly and Tito Mon 2 Quote Link to comment Share on other sites More sharing options...
rolly Posted December 11, 2013 Report Share Posted December 11, 2013 If you don't mind a drive to Whitby, I can help you. Buy the parts and I can help you install them. I have the brake piston rewind tool. There is more to replacing rear pads than just changing parts. You also need to lube the sliders and clean & lube the guides that the pads sit in. Otherwise, they will stick and drag on the rotors, causing premature wear. Man talk about Christmas spirit. Great offer!!!! This is a great forum. Quote Link to comment Share on other sites More sharing options...
Tito Mon Posted December 11, 2013 Author Report Share Posted December 11, 2013 I like this forum!!! REALLy,,,,, I appreciate,, Quote Link to comment Share on other sites More sharing options...
jkeaton Posted December 11, 2013 Report Share Posted December 11, 2013 (edited) If you don't mind a drive to Whitby, I can help you. Buy the parts and I can help you install them. I have the brake piston rewind tool. There is more to replacing rear pads than just changing parts. You also need to lube the sliders and clean & lube the guides that the pads sit in. Otherwise, they will stick and drag on the rotors, causing premature wear. True, true. Details I left out that are like second nature to me, I guess. My bad, thanks for adding. When I have to replace mine (or if someone else does theirs first) we will do a write up with pictures. Maybe start a FAQ/DIY section for how-to's for things like this. Whitby? My company has a manufacturing site in Whitby. May be up there sometime next year. Edited December 11, 2013 by jkeaton Quote Link to comment Share on other sites More sharing options...
FROGBOX Posted December 11, 2013 Report Share Posted December 11, 2013 True, true. Details I left out that are like second nature to me, I guess. My bad, thanks for adding. When I have to replace mine (or if someone else does theirs first) we will do a write up with pictures. Maybe start a FAQ/DIY section for how-to's for things like this. Whitby? My company has a manufacturing site in Whitby. May be up there sometime next year. I am a member on another forum for my daily driver (the Journey is the wife's). My car is a VW Jetta TDI. The site is www.tdiclub.com and I have been a member there for over 10 years. In that time, I have posted dozens of 'How to' tutorials on things like brake replacements, axle swaps, wiper transmission repairs, etc. We have a very large database of procedures for many generations of cars. I think it would be a good idea to have one here too. Like you suggested....a DIY section. Here is the thread I started on TDIClub: http://forums.tdiclub.com/showthread.php?t=60705 I haven't updated the thread in a few years, but there is a lot of great info with contributions from hundreds of members. Quote Link to comment Share on other sites More sharing options...
Isaiah6113 Posted December 11, 2013 Report Share Posted December 11, 2013 Frogbox, That truly is a neighbourly offer, such thoughtfulness! Who knows, maybe we'll meet up one day, I live in Oshawa. Matthew Quote Link to comment Share on other sites More sharing options...
2late4u Posted March 21, 2014 Report Share Posted March 21, 2014 well yesterday i changed out my rear pads,first time ever doing rear pads and it was a little harder than doing the fronts but after doing the one side the other side was a little easier.I used one of thoes $4.99 dice cubes to turn back the piston and as i read for it to fit a journey you have to grind off 2 of the 4. of the pegs to make it fit the face of the piston it wasnt as hard to turn it back as i thought it would be but it was a little difffcute. As i dont expect to have to do to many more brake changes it worked out ok.But if i was alot younger i would have spent the $39. plus tax for a big kit for rewinding the pistons one thiught was the kit from harbor freight didnt say it fit dodge vech. seems like it fit every vech. except them.oh my mainstreet has 65k miles on it and the inside pad was wore down pretty good probaly had about another 5k on them but wanted to put some on so we wouldnt have any brake problems while on a trip somewhere.If you watch that u tube vidieo on the 2009 brake change i couldnt get the caliper to come off withe the bracket like he showed i had to remove the 2 little caliper bolts from the carrier before getting them to come loose and you do need to wrenches to remove them as think frogbox was telling us, no big problem,also wagner thermoquite brake pads inst.said if the pads come with the shims come attached as they did not to use any stickey adhesive but to use a certain type of grease, but after removing the factory pads it looked like they used a dad of glue to the back of the pads, so ill find out in time if i should have used it also or done it like the instructions says ill report back later what i find out..... Quote Link to comment Share on other sites More sharing options...
2late4u Posted March 21, 2014 Report Share Posted March 21, 2014 g Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.