Jump to content

Dean H

Journey Member
  • Posts

    380
  • Joined

  • Last visited

  • Days Won

    44

Everything posted by Dean H

  1. Check your cabin air filter. In the slot up above your blower motor.
  2. Here are 2 pictures of the alternator cable connection down at the starter. The orange cable is the fusible link on the alternator battery feed cable. Cables disconnected from starter. The red cable on top goes to the TIPM positive battery stud. The alternator battery feed cable. Orange fusible link.
  3. Go here to my post- https://www.dodgejourneyforum.com/topic/18296-charging-system-101-with-diagrams/
  4. PCM plug - Same plug close up- The rest of the pin out is below.
  5. Circled is the fusible link that connects the alternator battery feed to the starter cable.
  6. Start here by reading this forum post. https://www.dodgejourneyforum.com/topic/18210-electrical-system-fyi-battery/ Read this forum post next. https://www.dodgejourneyforum.com/topic/18115-electrical-system-fyi-cables/
  7. First modification, that I did to my DJ. The air intakes funky tubes. My guess is they did something to quiet the intake noise ? I like a clean look in the engine bay. It was seriously messy cutting and grinding. I found rubber plugs on eBay, that were perfect for the job. Snorkel intake piece from air filter box to under hood. Air intake tube from engine to air filter box. Stock Dodge- Modified painted. Painted with Rust-Oleum bed liner. Light textured surface and sticks better than paint. Painted the air filter box. One reason, I chose to do this is that intact. The stock tubes had the coolest intake air temperature. With just the snorkel piece removed. The intake air temps ran around 10 to 12 degrees hotter. I had bought a " cold air intake" system. It only would have been the hottest air intake system. So no! I can actually access the transmission dipstick tube now! Dean
  8. All 3 of those use the same ground. Passenger strut tower 2 ground studs. Top square in picture. Clean them up. You should add a extra ground cable. Exactly, how I have the picture marked in orange. Use one of the studs on the engine mount. Read this post on grounds. https://www.dodgejourneyforum.com/topic/18115-electrical-system-fyi-cables/
  9. You need to go over the basics of electrical troubleshooting. Do you have a multimeter to read DC voltage? Here are basics you must do. Please read carefully. https://www.dodgejourneyforum.com/topic/18210-electrical-system-fyi-battery/ Dean
  10. The Dodge troubleshooting chart, for your codes point to the alternator or it's wiring. Check this cable. The alternator battery feed connects at the starter stud. Fusible link (orange wire) to 4 gauge to alternator stud. If your wire connections to the alternator are good. It may be the alternator. Electrical troubleshooting and maintenance. Do this it will help. Read my post- https://www.dodgejourneyforum.com/topic/18210-electrical-system-fyi-battery/ Process of elimination - 1) Battery terminal connections Clean up and tighten every cable connection. Negative battery terminal battery sensor. Exam sensor. Clean every connection on it. Installing sensor, you need to get the sensor seated all the way down. Before connecting any wires. Once seated spin sensor until all wires can be connected. Test the battery we need to know if it meets specifications. Problems on the journey - Read my post- https://www.dodgejourneyforum.com/topic/18115-electrical-system-fyi-cables/ 1) battery cables are 4 gauge. Too small should have been 2 gauge. The stock positive cables do seem to work. Clean connections are critical. The ground cables seem to be the problem spot. 2) Weak and not enough engine to chassis grounds. People have problems with the battery ground stud to engine block. I recommend owners do these 2 ground upgrades. Their cheap to do and needed. I used a 2 gauge cable from the large ground stud to engine stud. On the passenger side, use 4 or 6 gauge from engine mount to strut tower grounds. Connecting the pass side grounds to the battery ground. Through the engine block. Dean
  11. The picture of the positive battery terminal connection. That is the stock Dodge connection. 125k miles. You can see why clean connections are important. You see the rust. Covering the positive terminal is something you need to do. Go to Amazon and it's cheap. Fits perfectly. MGI SpeedWare Top Post Battery Terminal https://a.co/d/02C2W22J Same cable in picture above
×
×
  • Create New...