Camper

Mine is done also, 2016 Journey

I used ODBII on my 2016 Journey, without any issue.However, my scanner is connect to laptop (Autoenginuity) 

Just out off curiosity, how long the code you have to punch to get radio work on new vehicle?

Here is my conversation with Chrysler support:""

Could you please provide me the VIN number (serial number) of the car.

> I have no way of knowing what matches with what without getting the

> sales codes from that Journey.""Chrysler says to get the unlock code you need to have the VIN number from the donor car””

I done that swap, and it does required VIN from donor vehicle. When you get the radio from donor, it secured to that VIN. Dealer login to the their system and type the serial number from radio and donor VIN, then dealer obtained cod.When you install the radio into new vehicle, then it get registered to that vehicle after you punch the security code. Because, the code you received from dealer will unlock the radio and removed the anti theft soft look.:)

Yes, I change the oil, close to 10000 km, any way I just want to know, if the first statement was correct and dodge changed the interval for oil changing reminders.

DodgeCare, are you able to confirm that?

Does any one knows, if a Dodge changed interval for the oil changing message/reminder,from 10.000 km to 16.000 km?

 My 2016 Journey Crossroad do not provide the this warnings, even i draw 2000 km over oil limit (full synthetic oil) at 12000 km I do not receiving any warning to change the oil. Went to dealer today for full scan and we do not see any errors regarding to "oil life sensor"and "oil life monitor" and service manager show me, that the Dodge changed reminders to 16,000 km/10,000 ml. It hard to believe, they did that and do not provide the information to any where. 

Thanks

18 hours ago, bramfrank said:

 

You turn on the radio and enter it on the 'enter unlock code' screen.  Doesn't matter whether the engine is running or not.

 

 

That is NOT correct.

You need the serial number of the radio and the VIN of the TARGET vehicle; the one you are installing the radio in.

That is correct, and I am correct to , because in my post i say"" from one of the sticker"". one of them contained serial number.I`w done it this replacement on my 2012 Journey.

In order to get anti-theft code, you need to provide to your dealer VIN from donor vehicle and the and the code from one of the sticker from that radio, then dealer can obtained the code for you.

Does any one knows, if a Dodge changed interval for the oil changing message,from 10.000 km to 16.000 km?

 My 2016 Journey Crossroad do not provide the this warnings, even i draw 2000 km over oil limit (full synthetic oil) at 12000 km I do not receiving any warning to change the oil. Went to dealer today for full scan and we do not see any errors regarding to "oil life sensor"and "oil life monitor" and service manager show me, that the Dodge changed to 16,000 km/10,000 ml. I hard to believe, they did that and do not provide the information to any where. 

Thanks

On 12/12/2017 at 8:30 PM, bramfrank said:

 

For the record, those things on top ARE the microphones.  Two organised as an array and there a signal processor to provide noise reduction.

If you have holes on the bottom of your mirrors, then someone's been busy with a drill or the design has been changed (doubtful)

LOL

No it not a mic. Mic is built in into mirror and at the bottom of the mirror is two small holes for the mic.

More information: http://www.cumminsforum.com/forum/2013-general-discussion/1077802-hacking-uconnect-8-4a-8-4an.html

Try  holding JUST the driver's side temp up and down buttons

Eduardo831, any results on this intake resonator delete? Improvement? Does it worth $199? thx.

Can you please provide photos with light output at night? thx. 

Can you please provide the photo at night, with light output. Including the low beam and high beam.

Thanks, 

Does anyone consider to do this kind of modifications/additions?

Here is the few links for the parts: https://parts.moparonlineparts.com/auto-parts/2015/dodge/journey/sxt-trim/2-4l-l4-gas-engine/electrical-cat/headlamp-washers-wipers-scat

http://www.moparpartswebstore.com/p/Dodge_2016_JourneyRT/GROMMET--PUMP-Washer--Head-lamp-pump--Washer--Headlamp--Grommet-serviced-with-pump-only/42213682/05012060AA.html

Thanks,

Try this link http://www.driveuconnect.com/system/dodge/

Hope this will help.

Issue was resolved today, by installing the harness with relay and one resistor. Now all LED light bulbs (same as jkeaton use) working as a charm, low beam, high beam, fog lights

Here is the link, regarding to future of the Journey: http://www.allpar.com/news/2016/06/next-journey-italian-rwd-31993

What is your original size?

Glove box light isn`t LED as well

It work, i replaced on mine 2016,  with regular 194, no issue. 

Looks like is not installed correctly, maybe?

No, what I am say, I can push rpm up to 4000, however, the car do not change the gear, it stay on first one, so on that rpm I can push speed up to 60 km/h