Jump to content

khnitz

Journey Member
  • Posts

    62
  • Joined

  • Last visited

  • Days Won

    11

Everything posted by khnitz

  1. The tech at AZ indicated that the dark ring (pointed to with my small screwdriver in the photo below) is magnetized and provides the timing for the sensor. Based on the sensor position in the hub, it makes sense. And, that ring was decayed on the original hub. Now on to the hardware store to get a big-ass-chisel to seperate the hub from the spindle. The rotor hasn't broken loose yet, either (rustbelt repairs are such fun ?).
  2. Well, we're back in IL soo er than expected, but I ha e the replacement axle to install. The original one came out easily enough. So, I'm more confused. There really doesn't seem to be a tone ring anywhere that is a part of the CV axle. At the back of the wheel hub/bearing, there were signs of a rubber dust shield or something that spins with the hub - that seems to be the only thing close enough to the wheel speed sensor to have provided a means to count. It was all rusted and falling apart. The CV axle meets the hub/bearing too far back from the sensor to be the source of the count. I'll be going to Autozone in a bit to inspect a new wheel hub in person. As found: Old vs new CV axle: After clearing out the extra "seal" and rust:
  3. Oof - at least it is being covered under warranty for you! Are there any other steps they can take to prevent the same issue from happening with the new module?
  4. I continue to dig around for information on the exact location/structure of the tone wheel, and something I came across was a recall notice 15V-675. The recall work was to add extra sealing to prevent water ingress to the ABS unit that could result in a failure. A catastrophic failure from that water ingress would result in a C2200 fault code, and it definitely doesn't have that. Also, I checked their VIN and the recall work was performed in 2015. So, after confirming with their VIN, the Mopar PN for their FL CV axle is 68079565AB. I'll be going with a Duralast 14293N as the replacement. But, again, it will be a little bit before I am in IL again and can replace it. While the axle is out, I'll make sure to clear any debris out of the inside of the hub where the wheel speed sensor pokes through, too.
  5. I'm trying to find PC SW that will let me export data from my Foxwell NT510, but no luck so far. In the meantime, I manually plotted one of the data recordings I made. Yesterday, I was able to get the speed of the Journey up over 5mph by coasting downhill in neutral - I wanted to see how the wheel speeds tracked at greater than the 5mph that the TCS was limiting the vehicle to when in drive. BTW, once the speed when coasting had exceeded 20mph and I went back into drive the vehicle drove normally (but with the warnings lit). Anyway, here's what the data looked like (my guess is that the log is at once-per-second or so. So, I would say that somehow part of the LF tone wheel has deteriorated so that the wheel speed sensor is only able to partially count wheel speed during a rotation of the wheel. The other 3 sensors are tracking together. BTW, in previous replies, it was suggested to examine the vehicle wiring, as well. The harness looks clean and un-chewed, with no obvious spots of wear or corrosion, either. I would not say that the graphed results completely rule out a wiring issue also being a cause, but given that there were no sporadic readings when the rest of the sensors were measuring 0mph and that there are no codes for the sensor itself (just the code for the tone wheel due to the readings), I'm not inclined to think it's a wiring issue.
  6. Thanks for checking on that at O'Reilly's! I had to think a moment on the "5 ribs" advice, but then I got it. Yeah, I'll keep an eye out for that. And I'll do a little more research on the tone ring before pulling the trigger on the replacement axle. Definitely doesn't seem like it's part of the bearing/hub on the fronts, and looking through the sensor hole at the CV joint end while rotating the hub only showed a smooth surface...no timing "sprocket" teeth (like a gear) or holes (like a film reel). I will post further updates, though it may be while as we don't have a trip planned back to IL for a couple of months.
  7. We moved from IL to MI 6yrs ago, but travel back to visit family often. I'm usually pack tools to help with repairs while I'm in town. This weekend's trip included this wheel speed sensor issue on my in-laws' Journey, replacing the front brake pads on my sister's Scion xB, and replacing a seatbelt latch on a friend's Escape to finish the repair of damage from an accident (before and after images below - we took care of the bulk of its repairs on a couple of earlier trips) ?
  8. I went to Autozone this morning and measured one of their sensors, and it measured close to the RF OEM one at 4.7 MOhm. So, I went ahead and swapped the NTK for the Duralast from Autozone. I did have a friend lend me his small compressor, so I also blew out the sensor hole and spun the hub and kept blowing/clearing that are out. With the new-new sensor installed, I went for a drive and...same result. Tone Wheel signal fault C003002 - Left Front Tone Wheel-General Signal Failure. When I get back home, I'll pull the data I captured from all the wheel speed sensors on my test drive and post a graph here. It seems like the tone wheel is providing a signal only in part of the wheel rotation, so that is confusing the ABS system. I could not accelerate and exceed 5mph, as the traction control was limiting the vehicle speed. Interestingly, if I coasted down a hill to 20mph, then the system would allow the car to drive normally (though with various ABS/TCS/AWD warnings lit). While I was monitoring the speed readings during the test drive, the other 3 wheels were reading consistently together, while the LF wheel would sometimes read the same as the others and then other timed drop down low again. There is no DTC for the wheel speed sensor itself, so it must be providing the expected load of a good sensor to the ABS controller. That's all for this trip to my in-law's. I will post the data when I get back home later this weekend. Right now, I am leaning towards having to replace the LF CV axle (with the tone ring on it) in order to correct this issue. There are no other CV axle issues present (no groaning, no CV click in tight turns, etc.), so it's a shame that it has to be replaced just for the tone ring, but what can you do. At least I can do it for them, and they're not paying shop rates to diagnose and correct this.
  9. This morning I measured the RF (original, still good) sensor at 4.28 MOhm...hmmm. And the LF (new, NTK) sensor at .470 MOhm I did confirm my metef could measure a dead short correctly, too. I will have access to an air compressor this morning and I will try and blow the tone ring clear through the sensor opening and see if that helps (maybe there's flaked off rust built up in that area of the sensor opening). As you said, @John/Horace, looking at other pictures online the tone ring is pressed on at the end of the CV joint, but it doesn't have visible gaps or teeth, but likely there's something embedded in its construction to provide the rotational count to the sensor.
  10. Ok, thanks for those ideas. The old sensor ohmed out at 4.6M Ohm - that seems problematic. I should have time this weekend yet to measure the new NTK and also the other front sensor.
  11. Thanks for the help! Reading in other forums (for the Charger), some have reported problems with anything other than Mopar wheel speed sensors. So, in full disclosure, the sensor I installed is from NTK. Working for a Tier1 myself, and being familiar with some of the players in the sensor world, NTK seems like a reasonable replacement option. But, I'm open to learning from others' experieces.
  12. I'm helping my in-laws with a repair on their 2014 Dodge Journey 3.6 AWD. I have a Foxwell NT510 scanner that I am using to help with the diagnosis. They had the ABS, Traction Control and Service AWD warning/lights lit, and the code that came up was for a bad LF wheel speed sensor. I replaced the sensor and cleared the codes. The codes are not coming back, but, the traction control is engaging at about 4mph and it will go no faster. When I did a live read of all 4 wheel speed sensors, the RF, LR and RR all read 4mph, but the LF sensor gave erratic readings (1mph, etc.) When the traction control light was active. And...in this condition, there are no ABS codes stored. So, next steps...I'm thinking the LF tone ring is bad or dirty/clogged? Is the tone ring built into the wheel hub, or does it slip on to the end of the CV axle/joint? My in-laws live 2 states away, so I just want to be prepared for my next trip here to put it all right. In the meantime, I've pulled the 40A fuse for the ABS/TCS, so that the Journey can be driven normally (just means the ABS/TCS is unavailable). TIA
×
×
  • Create New...