bigunclejethro

I think VX is dynomax but I could be wrong. They offer a no drone muffler that I was looking at but I already spent too much money on my exhaust...

The exhaust cutout has been installed and the results aren't as dramatic as I was expecting, but there is a reasonable reduction in cabin noise without a big drop in engine power. I will post images to explain what I've done. So if anyone is still paying attention, stay tuned!

The new tires will not be the same size as the old ones but it does look like they are rated for the same pressure as the stockers, so I suppose there is no concern. Thanks for the feedback anyway. I found a good website (can't remember the name now) that spits out how far off the speedo would be at. I'm planning to go from 225/55/19's to 245/55/19's, and the speedometer difference at 60 would now be 64, which to me is not a big deal. You should be able to get whatever adjusted at the dealership though.

I'm planning to upgrade tires this fall and it just occurred to me that the pressure rating is higher than the stockers. Will this set off any alarms or cause problems with the tire pressure sensors?

Keeping you guys posted (if anyone is still interested), the wireless controller is installed and I have the switch hidden, but conveniently in reach from the drivers seat. I did not cut into the vehicles wiring, but got a cigarette lighter adapter with a remote extension, cut the extension off and connected the controller to that. This way, if I decide I don't want the valve or want to sell the car or whatever, it will all come out very easily. I'm hoping this week to make up a few valve plates with varying blockages (planning anywhere from 25%-75%), and will have the valve installed hopefully this weekend. I'll report back soon with pictures and results!

Anyone else with powdercoated blacktop rims experience this? I never hear when it happens, but the next time I was my car I usually find another chip in my wheels. They look like steel wheels to me underneath and I'm afraid of them rusting. Even if they were aluminum, the roads are so covered in salt and sand in CT in the winter, they wouldn't stand a chance. Anyone have any quick fixes that aren't super obvious?

Sorry to bring this back from the dead, but Darkpaw mentions speaker wires available in the rear driver cargo space. Are these available on all models or just those with premium sound? I find with the windows open, I'm almost maxed out on volume, so I want to add two rear speakers. Anyone gone through the install or can point me to someone who has?

I also deleted mine, but also replaced the stock mufflers with xlerators (similar sound to flowmaster). You'll get a much more aggressive tone, well worth the cost and weight savings! I'd be interested in hearing just the resonator delete as well.

Bigtsr I believe that's the one. Feels like a lever inside the hole but I didn't want to pull it and find out. I will look for this drain plug by the brake pedal. I also noticed behind the stereo down low there is also a grommet that brings out a cable just above the driveshaft. I'm thinking of using this one as it is right where I want to put the wireless controller. Either way, this project is a few weeks off still as I have to put some time and money into my other car at the moment. Thanks for the help

I will look into that. I would like to keep the controller in the console so I can keep an eye on its status but under the dash would work too. I noticed there is a plastic snap in grommet on the inside front of the console. Any idea why that is there any where it goes to?

Similar concept I suppose. When I find the plate that works the best for me I don't intend on changing it out though. Anyone have any good instructions for removing the center console? Or is there a good place to run the signal wire out for the cutout that I don't have to take anything apart for?

Well the valve came in yesterday and it should be pretty easy to hook everything up so I'm going to go for it. I'm going to make a few different valve plates with varying hole sizes, and start with the largest and see if I can find the right balance between noise and performance. MAP sells a universal damper valve with just a 9/16 hole in it, but that seems way to small to me. I'd be afraid to overtake anyone on the highway with that. If anyone's interested, here's the link. http://www.maperformance.com/map-universal-3-inline-exhaust-damper.html Anyone have a simpler idea? The cost of the valve and controller is less than what my mufflers cost, so I'm not in a rush to take those out.

It wouldn't be any more restrictive than the stock muffler and resonator. I appreciate the comment but the back pressure debate is not what I was going for.

The resonator is gone, and in its place at the moment I have clamped a piece of straight pipe. What I plan to do is put the valve in where the pipe is. It's wont be tee'd off to anywhere so the exhaust will still go through the mufflers. I found the resonator made the exhaust high pitched and ricery with the mufflers I picked, but taking it off really opens up the noise level and gives the tone I want. I'm just adding an adjustable obstruction in the exhaust line to keep the same tone but adjust the volume.

I recently installed a set of aftermarket mufflers and deleted the resonator. The car sounds awesome (especially for a V6) but it can be really obnoxious sometimes. I ordered an exhaust cutout valve from QTP with a wireless controller and am planning to stick it inline with my exhaust to silence it as much as I want whenever I want/need to. I'm thinking I will want to put some holes in the valve plate to not completely restrict the flow, but I've never used a cutout before and have no idea how large to drill. Thoughts anyone?

I have been thinking about niteshade but Im not to keen on sanding my lights and I don't want it to be too dark. I did have them plastidipped for a while, but am going to be taking some longer trips across the US and don't want to worry about cops pulling me over. That's why I was thinking of painting the inside. How easy is niteshade to remove and can it be applied without sanding?

I love the crossroad tail lights. I had mine tinted for a while but got tired of the look. If the red of the lights was a little darker than the red of my car, I would be happy. Anyone know where I can get a cheaper set of replacement light housings? Rock auto has them for over 100/pc. If I could get them cheaper I might consider it. Thanks for the feedback!